Acrel ADL400N-CT Three-Phase Energy Meter DIN-rail three-phase energy meter for low-voltage systems using current transformers. Measures imported and exported active and reactive energy, plus voltage, current, power, power factor, frequency and harmonics. RS485 Modbus RTU communications for integration with compatible energy-management, monitoring and building-control systems. Acrel ADL400N-CT three-phase energy monitoring The Acrel ADL400N-CT is a three-phase energy meter for low-voltage electrical systems with current-transformer measurement. It is suitable for monitoring energy consumption and energy flow in commercial buildings, workshops, distribution boards, solar PV installations, battery-storage systems and other three-phase electrical installations. The meter provides measurements for positive and negative kWh and kvarh, individual phase energy, voltage, current, active power, reactive power, apparent power, power factor and frequency. It also measures harmonics from the 2nd to the 31st order and communicates through RS485 using Modbus RTU. Key features Three-phase energy measurement with CT-connected current inputs. Class 0.5S active-energy accuracy and Class 2 reactive-energy accuracy. Measures positive and negative kWh and kvarh, including A, B and C phase positive kWh. 12-digit LCD display, three-key programming, infrared communications and RS485 Modbus RTU. DIN 35mm rail mounting for panel and distribution-board installations. Where to use the Acrel ADL400N-CT energy meter The Acrel ADL400N-CT three-phase energy meter is suited to monitoring incoming supply, sub-distribution circuits, solar PV output, inverter AC connections, battery-storage systems, generator circuits and larger three-phase loads. It can be used where current transformers are required because the circuit current exceeds the direct-meter connection limit or because a CT-based monitoring arrangement is preferred. It supports three-phase four-wire and three-phase three-wire wiring arrangements, using direct connection or current transformers as shown in the manufacturer wiring diagrams. CT ratio selection, phase orientation, protection and communications wiring must be designed for the specific installation. This meter should be installed by a competent electrician or controls engineer. Energian can provide UK expert support for monitoring-system selection, Modbus integration and compatible solar, battery or energy-management systems. Technical specifications Product Acrel ADL400N-CT Three-Phase Energy Meter Meter type Three-phase low-voltage energy meter Mounting method DIN 35mm rail Applicable standards IEC 62053-21, IEC 62053-22 Measurement and functions Active energy measurement Positive and negative kWh Reactive energy measurement Positive and negative kvarh Phase energy measurement A, B and C phase positive kWh Electrical parameters measured Voltage, current, active power, reactive power, apparent power, power factor and frequency Harmonic measurement 2nd to 31st harmonic Display 12-digit LCD Key programming 3 keys Pulse output kWh active-energy pulse Data functions Maximum demand, frozen data for the previous 48 months and previous 90 days, and date/time functions are listed as optional Infrared communication Supported Voltage performance Nominal voltage options 3 × 100V; 3 × 380V; 3 × 57.7/100V; 3 × 220/380V Voltage consumption <10VA per phase Voltage input impedance >2MΩ Voltage accuracy ±0.2% Current, energy and communication Maximum current 80A direct connection; 6A CT connection Current consumption <1VA Current accuracy ±0.2% Frequency range 45–65Hz Frequency accuracy ±0.2% Active-energy accuracy Class 0.5S Reactive-energy accuracy Class 2 Clock accuracy ≤0.5 seconds per day Active-energy pulse width 80 ± 20ms Active-energy pulse constant 1,000imp/kWh; 10,000imp/kWh Communication interface RS485 Communication protocol Modbus RTU Operating environment Operating temperature -25°C to +55°C Storage temperature -40°C to +70°C Humidity ≤95%, non-condensing Maximum altitude <2,000m Installation and connections Supported wiring arrangements Three-phase four-wire via CT; three-phase four-wire direct connection; three-phase three-wire via CT; three-phase three-wire direct connection RS485 terminals Terminals 21 and 22; A1 and B1 Active-energy pulse terminals Terminals 17 and 18; Ep+ and Ep- Direct-connection terminal torque Maximum 4.0N·m CT-connection terminal torque Maximum 2.0N·m Documents available for download Acrel ADL400N-CT manual Shipping and UK expert support Shipping is available to the UK, Ireland, Africa, the Caribbean and worldwide. If a shipping rate is not shown at checkout, contact us on +44 2080 640335 or [email protected] for a quote. UK expert support is available for product questions, CT selection, Modbus communications and energy-monitoring system design. Contact Energian by phone, email or live chat, or visit our office for an in-person consultation.
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.
