Katool KT-H100: a 10,000 lb two-post lift that stands about 110 inches The number to look at first on this lift is not its capacity. It is its height. The KT-H100 uses a base-plate layout — the equalisation runs sit in a shallow plate bolted across the floor between the columns, with nothing spanning the top — and the result is a two-post lift whose columns stand about 110 inches, 110.25" (2,800 mm) on the specification sheet. That is what makes it installable in a building where a lift with an overhead assembly simply will not go: a home garage with a finished ceiling, a unit with a sectional door track, a shop with a sprinkler run or a low header over the bay. What that height buys, you pay for on the floor: the base plate is a low ramp across the bay that a creeper, a drain pan and a transmission jack all have to cross. If your ceiling is generous, a clear-floor lift is nicer to work around; if your ceiling is the constraint, this is the layout that works at all. Above the plate the KT-H100 is a conventional 10,000 lbs (4,500 KG) symmetric lift with dual hydraulic chain-drive cylinders and a manual safety release on both columns. Will It Fit? Six things decide it and every one is the buyer's to confirm before the truck arrives. We cannot see your building, your slab or your electrical panel. Ceiling. The lift stands about 110 inches — 110.25" (2,800 mm) — but that only tells you whether the columns fit. What governs your roof is the height of the tallest vehicle you intend to raise plus the rise you want under it. Floor width. 142 inches overall, listed as 142.25" (3,614 mm), with 128" (3,250 mm) across the outside of the columns and 110.25" (2,800 mm) between their inside faces. The inside figure is your working room; the outside figure has to fit the bay, with space to walk beyond it. Drive-through. 94.5" (2,400 mm) between the columns. That, not the capacity, is what stops a wide vehicle. Concrete. Minimum 5.9 inches thick at a compressive strength of at least 3,000 psi, level and unbroken under the anchor pattern — no expansion joint, no crack, no patch. Confirming the slab is the owner's responsibility and it is the most common reason an installation stops on the day. Power. A 220V/60HZ/1PH hydraulic system is standard, with 110V/60HZ/1PH available as an option. Decide before it ships and get the circuit run in advance. The base plate. Make sure everything you roll across the bay can cross it, and that it does not land on a floor drain or an expansion joint. Two cylinders, and what that buys you Each column carries its own hydraulic chain-drive cylinder off a single power unit, rather than one cylinder dragging both sides through a linkage. The effect shows up with a real vehicle rather than on a spec sheet: a pickup with a heavy engine forward and an empty bed is an offset load, and on a lift whose sides do not track together that difference is absorbed by the arms, the pads and the vehicle instead of by the structure. Two cylinders in step also keep the mechanical locks engaging at matching heights on both columns. A release on both sides, and guardrails with a tool box in them The safety locks hold a raised vehicle on steel, not on hydraulic pressure, so lowering means releasing them — and here that release is manual and duplicated on both columns. You are not walking around a loaded lift to find one handle. Two smaller details tell you this was drawn by somebody who has worked in a bay: rubber pads protect the door-opening area, so a door swung open at working height meets rubber rather than painted steel, and the feet-protection guardrails at the base double as a tool box, which sounds like a gimmick until you notice the alternative is a socket set on the floor exactly where the lift comes down. Arms, adaptors and awkward vehicles Arm reach is what usually decides whether a vehicle can be picked up at its designated lift points, and here it runs from 30.75" (780 mm) to 50.5" (1,280 mm) in two stages. The lift raises to 70.75" (1,800 mm) at the top of the pad, giving 67 inches of rise under the arms, and drops to 4.25" (110 mm) so a low car drives over the arms instead of onto ramps. Extension support adaptor sets of +30mm and +120mm come with the lift, which is what a truck or SUV with high pinch welds needs and what many lifts in this class charge extra for. Perfect For Home garages with a finished or obstructed ceiling, where an overhead-beam lift was never an option. Independent shops fitting a lift into an existing building rather than designing a building around a lift. Brake, exhaust, suspension and tyre work on cars and light trucks, where standing height under the vehicle is the whole point. Long projects and restorations, where a vehicle sits for days on mechanical locks instead of on stands. What's in the Box Two columns with the base-plate assembly and dual hydraulic chain-drive cylinders Symmetric arm set with adjustable pads Extension support adaptor sets, +30mm and +120mm Rubber door-opening protection pads Feet-protection safety guardrails with tool box Hydraulic power unit, 220V/60HZ/1PH, or 110V/60HZ/1PH if you specify the option Anchors and any slab work are not part of the crate. Specifications Lifting capacity 10,000 lbs (4,500 KG) Overload testing published 115% dynamic, 150% static Net weight 1,256 lbs (570 KG) Overall height About 110 inches; 110.25" (2,800 mm) on the spec sheet Overall width 142 inches; 142.25" (3,614 mm) on the spec sheet Outside the columns 128" (3,250 mm) Inside the columns 110.25" (2,800 mm) Drive-through clearance 94.5" (2,400 mm) Maximum lifting height, top of pad 70.75" (1,800 mm) Maximum rise under the arms 67 inches Minimum height 4.25" (110 mm) Minimum pad height 4 inches Arm reach, two stages 30.75" (780 mm) to 50.5" (1,280 mm) Supplied adaptors +30mm and +120mm extension sets Power unit 220V/60HZ/1PH standard; 110V/60HZ/1PH optional Concrete required 5.9 inches minimum thickness, 3,000 psi minimum Certification, stated plainly Katool markets the KT-H100 as CE approved and certified, with the 115% dynamic and 150% static figures above. Take that for what it is. CE is a European conformity marking resting on the manufacturer's own declaration against European directives; it is not the same document as a North American third-party lift safety listing, and it does not stand in for one. For a private garage and for many independent shops the distinction never arises. It does arise for some commercial insurance policies, for fleet and municipal operations, and for jurisdictions whose code names a specific listing. Ask your insurer, your inspector or your employer what they require before you order, not after the lift is anchored to your floor. Shipping and delivery The KT-H100 ships by freight truck to addresses in the lower 48 states. Freight is quoted live at checkout against the address you enter, so what you see is a current carrier rate rather than an estimate that has aged. It arrives crated on a standard trailer and getting it to the ground is the receiver's responsibility — a forklift, a machine, or a plan and some help. Where that is not realistic, collecting from the carrier's local terminal is usually easier, because the terminal already has the equipment. A residential delivery address carries a residential fee, applied at checkout when you select that option. Inspect before you sign. Walk the crate and the columns, look for crushed corners, gouges, shifted banding and oil, and write anything you find on the bill of lading while the driver is still there. Photograph it. A clean signature is the carrier's evidence that the shipment arrived undamaged. Warranty Katool publishes a written warranty document covering this lift. The terms are the manufacturer's to state and they change, so ask us for the current copy before you order if the coverage is part of your decision. One warning applies to every hydraulic lift whoever built it: if something fails, do not take the power unit, a cylinder or a lock mechanism apart before a claim is open. A disassembled component is normally treated as a modified one, which is the fastest way to lose coverage you would otherwise have had. Photograph the fault, note the serial number, and call first. Contact us if you want the fitment figures checked against your bay before you order. Katool KT-H100 2 Post Car Lift Product Features 10,000 lbs lifting capacity CE Approved and Certified. It has adopted the 115% dynamic loading capacity standard and was 150% static loading capacity tested Manual safety release from two sides Symmetric arm Base plate design Dual Hydraulic Chain-Drive Cylinders Rubber pad door opening protection Comes with extension support adaptor sets of +30mm and +120mm Feet-protection safety guardrails with tools box Top-level hydraulic system with 220V/60HZ/1PH and 110V/60HZ/1PH (Optional) Pick Up and Delivery Call, text, or chat with us if you have questions. 866-774-7743
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.