HARMONIZE HMN Series Winglets — Yamaha YZF-R1 (2015–2019) Model: HMN-15R1 QS The 2015 R1 wasn't a refresh, it was a rebuild around the M1. Yamaha modeled that generation's bodywork directly on its factory MotoGP bike and backed it up with titanium fracture-split connecting rods, a first for any production motorcycle, plus a 6-axis IMU lifted straight from the racetrack. The HMN-15R1 QS carries that same MotoGP-first thinking to the nose of the bike: a four-piece, 3D-printed wing set that mounts with 3M VHB tape, no drilling required. Shaped by the Generation That First Wore the M1's Face Every panel on the 2015–2019 R1 traces back to the same design brief as Yamaha's factory MotoGP bike from that era, part of why this generation still reads as a race bike more than a decade later. HMN-15R1 QS wings are scanned and shaped specifically for that fairing line, not adapted from the newer bodywork, so the fit follows the same lines Yamaha drew for that M1-inspired nose. No-Drill Mounting, Same Approach as the Rest of the HMN Line Like the rest of HARMONIZE's HMN Series, these wings mount with 3M VHB instead of screws, a structural acrylic tape borrowed from the auto industry, where it's trusted to bond body panels and trim without rivets. Prep the surface with the included adhesion promoter, give the bond its full cure time, and the wings are designed to hold through sustained wind load with no holes left in the fairing if you ever remove them. Key Features Four-piece design, main and secondary wing per side, shaped specifically for the 2015–2019 fairing 3D-printed, high-precision surfaces exclusive to HARMONIZE's manufacturing process 3M VHB mounting: no drilling, no permanent change to the bodywork Carbon fiber reinforced thermoplastic for heat resistance and long-term toughness without added weight Specifications Series HARMONIZE HMN Series Model HMN-15R1 QS Fitment Yamaha YZF-R1, 2015–2019 Content Four-piece (main + secondary wing, both sides) Material Carbon fiber reinforced thermoplastic Installation 3M VHB, no drilling What's in the Box Winglet, brake side, main wing (with 3M VHB) × 1 Winglet, brake side, secondary wing (with 3M VHB) × 1 Winglet, clutch side, main wing (with 3M VHB) × 1 Winglet, clutch side, secondary wing (with 3M VHB) × 1 3M adhesion promoter × 1 Cleaning pad × 1 Installation instructions × 1 Installation No drilling, no screws. Clean and prep the mounting area with the included pad and adhesion promoter, then position each wing using the instructions as a guide. Let the bond reach full cure before riding — VHB builds strength over time, not instantly on contact. Product photos on this page show the winglets fitted to a stock YZF-R1 fairing. FAQ Will this fit a 2020 or newer R1? No. This kit is shaped for the 2015–2019 fairing. The 2020–2024 generation uses different bodywork and needs the HMN-20R1 QS instead — check your model year before ordering. Will VHB tape actually hold at speed? Yes, when the surface is prepped properly. 3M VHB is a structural-grade tape used in the auto industry to bond panels without rivets or screws. Clean the surface, apply the included adhesion promoter, and let the bond fully cure before riding. Can I remove these later? Yes. There's no drilling involved, so there are no holes to fill in if you remove the wings or sell the bike. Is this legal for street riding? Aftermarket bodywork rules vary by country and state. Check your local vehicle regulations before installing and riding on public roads. Why HARMONIZE HARMONIZE shapes every wing for the exact bike it's built for, generation by generation, not one design stretched across years of bodywork changes. The HMN-15R1 QS is scanned and cut for the fairing that first carried Yamaha's MotoGP styling onto the street, giving that generation of R1 an aero upgrade that fits like it was drawn for it, because it was.
Checkout happens on the official store. This page mirrors catalog facts in plain HTML for direct reading and crawlability.
